TECHNICQLL - DIY ACCESSORIES

Manufacturers

Suppliers

Viewed products

10x ENAMEL FIX FILLER FOR CERAMIC BATH BASIN SINK SHOWER BASE URINAL GAS COOKER WASHING MACHINE NEW

P-805

New product

Damaged bath?

Cracked enamel in the sink or urinal?

Damaged lacquer of a gas cooker or of a wasching machine?

A BRAND NEW

10 x ENAMEL FIX FILLER (NOT PAINT)

FOR CERAMIC BATH BASIN SINK SHOWER BASE URINAL GAS COOKER WASHING MACHINE NEW ETC

20g + 4g


HIGH QUALITY PRODUCT

More details

10 Items

£64.99

More info

Damaged bath?

Cracked enamel in the sink or urinal?

Damaged lacquer of a gas cooker or of a wasching machine?


Use the touch-enamel from Technicqll. This two-component, epoxy product is resistant to yellowing, tough and has an incredibly high opacity (just the millimeter layer to thoroughly cover the damaged coating).

A BRAND NEW

10 x ENAMEL FIX FILLER (NOT PAINT)

FOR CERAMIC BATH BASIN SINK SHOWER BASE URINAL GAS COOKER WASHING MACHINE NEW ETC

20g + 4g


HIGH QUALITY PRODUCT

ADVANTAGES:

  • Strongly binds the broken pieces of ceramic and enamel.
  • It's resistant to water and a variety of harsh chemicals (including detergents and solvents).
  • Enamel Fix does not reduce its volume during the cure
  • Resistant to temperatures from -40 to +100 °C.
  • Dope has the most optimal shade of white and very high gloss
  • The resulting coating is resistant to scratches

FEATURES:

  • epoxide basis
  • does not contain solvents
  • universal
  • water and temperature resistant
  • resistant to aggressive chemical agents
  • when dry, can be mechanically processed
  • based on non-yellowing resin
  • high content of pigments

USAGE:

Enamel can be used for:

  • repair of acrylic, ceramic, enamelled bath
  • repair of a washbasin, shower base, sink
  • repair of urinal, toilet
  • repair of broken tiles


but also to repair the bodies of washing machines, refrigerators, gas cookers, lacquered furniture.

ADVANTAGES:

  • high ability of protection against corrosion
  • safe when used
  • connects metals, ceramics, plastics
  • to be used both inside and outside
  • resistant to washing means
  • allows to aesthetically restore damaged elements
  • durable colour, resistant to ageing
  • high coverage capacity

Usage:

  1. Clean and degrease the surfaces.
  2. Squeeze from the tube into a plastic bowl 5 grams of enamel - up to internal rim of the bowl.
  3. Cut the ending (4mm) of applicator (B ingredient) with a knife, and to already put mortar introduce 30 drops (1 gm) of solidification agent.
  4. Then precisely mix the composite ingredients with a spoon (for at least 2 minutes).
  5. There is a sticker made of polyethylene foil in the package. The sticker serves to make even edges, and to protect not damages surface against getting dirty by mortar.
  6. the hole with proper size shall be cut out in the sticker, adjusted to the damaged defect, remove protective paper and stick it prior to put enamel.
  7. Excessive composite applied with a spoon to shall be collected and equally distributed (to get even, flat surface - without excessive).
  8. One needs to remember to remove protective sticker right after partial drying of the mortar (that is, no later than approx. 30 minutes since its application). But clear polyethylene foil allows to get smooth and glare surface.
  9. Foil is applied on the surface, covered with mortar (immediately after removal of protective sticker) and after delicate smoothing with fingers, then it is kept to complete solidification of composite.
  10. On vertical surfaces (to avoid flowing down of the thicker layer of enamel), the mortar shall be applied with thinner layers, after the previous one is solidified, that is every 2 hours.       Scratches and cracks to be filled using i.e. toothpick. In order to receive smooth, glare surface one must remember to gently apply onto the final, last not solidified layer of mortar clear smoothing foil, and remove it only after 24 h.

 

TIPS AND RECOMMENDATIONS:

  • heat the product to room temperature prior to mixing the ingredients
  • do not use to connect / fill in PP, PE and PTFE.
  • the surface to be repaired shall be cleaned from corrosion and loosely connected old background, and then carefully degrease and dry,
  • it is also recommended to dim it with small sandpaper, taking care not to scratch the non-repaired surface

STORAGE:

Store in temperature from 5°C to 25°C.